int32_t adpd188_init(struct adpd188_dev **device, struct adpd188_init_param *init_param);

int32_t adpd188_remove(struct adpd188_dev *dev);

int32_t adpd188_reg_read(struct adpd188_dev *dev, uint8_t reg_addr, uint16_t *reg_val);

int32_t adpd188_reg_write(struct adpd188_dev *dev, uint8_t reg_addr, uint16_t reg_val);

int32_t adpd188_mode_get(struct adpd188_dev *dev, enum adpd188_mode *mode);

int32_t adpd188_mode_set(struct adpd188_dev *dev, enum adpd188_mode new_mode);

int32_t adpd188_fifo_status_get(struct adpd188_dev *dev, uint8_t *bytes_no);

int32_t adpd188_fifo_clear(struct adpd188_dev *dev);

int32_t adpd188_fifo_thresh_set(struct adpd188_dev *dev, uint8_t word_no);

int32_t adpd188_interrupt_get(struct adpd188_dev *dev, uint8_t *flags);

int32_t adpd188_interrupt_clear(struct adpd188_dev *dev, uint8_t flags);

int32_t adpd188_interrupt_en(struct adpd188_dev *dev, uint8_t flags);

int32_t adpd188_gpio_setup(struct adpd188_dev *dev, struct adpd188_gpio_config config);

int32_t adpd188_gpio_alt_setup(struct adpd188_dev *dev, uint8_t gpio_id, enum adpd188_gpio_alt_config config);

int32_t adpd188_sw_reset(struct adpd188_dev *dev);

int32_t adpd188_clk32mhz_cal(struct adpd188_dev *dev);

int32_t adpd188_slot_setup(struct adpd188_dev *dev, struct adpd188_slot_config config);

int32_t adpd188_adc_fsample_set(struct adpd188_dev *dev, float freq_hz);

int32_t adpd188_adc_fsample_get(struct adpd188_dev *dev, float *freq_hz);

int32_t adpd188_smoke_detect_setup(struct adpd188_dev *dev);

/**
 * @union adpd188_phy_init
 * @brief Communication physical protocol initialization structure. Can be I2C
 *        or SPI.
 */
union adpd188_phy_init {
	/** I2C initialization structure. */
	struct i2c_init_param i2c_phy;
	/** SPI initialization structure. */
	struct spi_init_param spi_phy;
};
?
/**
 * @enum adpd188_phy_opt
 * @brief Types of physical communication protocol.
 */
enum adpd188_phy_opt {
	/** SPI communication. */
	ADPD188_SPI,
	/** I2C communication. */
	ADPD188_I2C
};
?
/**
 * @enum adpd188_mode
 * @brief ADPD188 operation modes.
 */
enum adpd188_mode {
	/** Standby mode. */
	ADPD188_STANDBY,
	/** Program mode. */
	ADPD188_PROGRAM,
	/** Normal mode. */
	ADPD188_NORMAL
};
?
/**
 * @enum adpd188_interrupt
 * @brief Interrupt flags of the ADPD188.
 */
enum adpd188_interrupt {
	/** Slot A conversion interrupt flag. */
	ADPD188_SLOTA_INT = 0x1,
	/** Slot B conversion interrupt flag. */
	ADPD188_SLOTB_INT = 0x2,
	/** FIFO threshold reached interrupt flag. */
	ADPD188_FIFO_INT = 0x4
};
?
/**
 * @struct adpd188_gpio_config
 * @brief GPIO level configuration.
 */
struct adpd188_gpio_config {
	/** GPIO ID (0 or 1) */
	uint8_t gpio_id;
	/** GPIO polarity */
	uint8_t gpio_pol;
	/** Status of the GPIO driver (driven or open-drain) */
	uint8_t gpio_drv;
	/** GPIO enable (only for GPIO0) */
	uint8_t gpio_en;
};
?
/**
 * @enum adpd188_gpio_alt_config
 * @brief GPIO source configuration.
 */
enum adpd188_gpio_alt_config {
	/** GPIO backwards compatible with the ADPD103 INT functionality. */
	ADPD188_ADPD103 = 0x00,
	/** Interrupt function provided on GPIO. */
	ADPD188_INT_FUNC = 0x01,
	/**
	 * Asserts at the start of the first time slot and deasserts at end of last
	 * time slot.
	 */
	ADPD188_ACTIVE_PULSE = 0x02,
	/** Time Slot A pulse output. */
	ADPD188_SLOTA_PULSE = 0x05,
	/** Time Slot B pulse output. */
	ADPD188_SLOTB_PULSE = 0x06,
	/** Pulse output of both time slots. */
	ADPD188_ANYSLOT_PULSE = 0x07,
	/** Output data cycle occurred for Time Slot A. */
	ADPD188_SLOTA_OUT = 0x0C,
	/** Output data cycle occurred for Time Slot B. */
	ADPD188_SLOTB_OUT = 0x0D,
	/** Output data cycle occurred. */
	ADPD188_ANYSLOT_OUT = 0x0E,
	/**
	 * Toggles on every sample, which provides a signal at half the sampling
	 * rate.
	 */
	ADPD188_HALF_SAMPLING = 0x0F,
	/** Output = 0. */
	ADPD188_OUT_LOW = 0x10,
	/** Output = 1. */
	ADPD188_OUT_HIGH = 0x11,
	/** 32 kHz oscillator output. */
	ADPD188_32KHZ_OSC = 0x13
};
?
/**
 * @enum adpd188_slots
 * @brief ADPD188 time slots.
 */
enum adpd188_slots {
	/** First slot. */
	ADPD188_SLOTA,
	/** Second slot. */
	ADPD188_SLOTB
};
?
/**
 * @enum adpd188_slot_fifo_mode
 * @brief The way a time slot stores data in the FIFO.
 */
enum adpd188_slot_fifo_mode {
	/** No data to FIFO. */
	ADPD188_NO_FIFO,
	/** 16-bit sum of all four channels. */
	ADPD188_16BIT_SUM,
	/** 32-bit sum of all four channels. */
	ADPD188_32BIT_SUM,
	/** Four channels of 16-bit sample data for the time slot. */
	ADPD188_16BIT_4CHAN = 0x4,
	/** Four channels of 32-bit sample data for the time slot. */
	ADPD188_32BIT_4CHAN = 0x6
};
?
/**
 * @struct adpd188_slot_config
 * @brief Slot configuration initialization structure.
 */
struct adpd188_slot_config {
	/** Time slot ID. */
	enum adpd188_slots slot_id;
	/** Enable time slot. */
	bool slot_en;
	/** Time slot FIFO mode. */
	enum adpd188_slot_fifo_mode sot_fifo_mode;
};
?
/**
 * @struct adpd188_dev
 * @brief Driver descriptor structure.
 */
struct adpd188_dev {
	/** Communication physical type. */
	enum adpd188_phy_opt phy_opt;
	/** Communication physical descriptor. */
	void *phy_desc;
	/** GPIO 0 descriptor. */
	struct gpio_desc *gpio0;
	/** GPIO 1 descriptor. */
	struct gpio_desc *gpio1;
};
?
/**
 * @struct adpd188_init_param
 * @brief Driver initialization structure.
 */
struct adpd188_init_param {
	/** Communication physical type. */
	enum adpd188_phy_opt phy_opt;
	/** Communication physical initialization structure. */
	union adpd188_phy_init phy_init;
	/** GPIO 0 initialization structure. */
	struct gpio_init_param gpio0_init;
	/** GPIO 0 initialization structure. */
	struct gpio_init_param gpio1_init;
};

#include 
#include 
#include "adpd188.h"
?
void main()
{
    struct adpd188_dev *adpd_desc;
    struct adpd188_init_param adpd_init;
    int32_t ret;
    uint16_t reg_data;
?
    adpd_init.phy_opt = ADPD188_SPI;
    /* SPI initialization is generally dependent on the platform used */
    adpd_init.phy_init.spi_phy.extra = NULL; /* Platform dependent; this is a dummy value */
    adpd_init.phy_init.spi_phy.chip_select = 0; /* Platform dependent; this is a dummy value */
    adpd_init.phy_init.spi_phy.max_speed_hz = 6000000; /* Platform dependent; this is usually a good value */
    adpd_init.phy_init.spi_phy.mode = SPI_MODE_3; /* This should always be the mode */
    /* GPIO initialization is generally dependent on the platform used */
    adpd_init.gpio0_init.number = 1; /* Platform dependent; this is a dummy value */
    adpd_init.gpio0_init.extra = NULL; /* Platform dependent; this is a dummy value */
    adpd_init.gpio1_init.number = 2; /* Platform dependent; this is a dummy value */
    adpd_init.gpio1_init.extra = NULL; /* Platform dependent; this is a dummy value */
?
    ret = adpd188_init(&adpd_desc, &adpd_init);
    if (ret != 0)
        return -1;
?
    /* Read device ID. For ADPD188BI it must be 0x16. */
    ret = adpd188_reg_read(adpd_desc, ADPD188_REG_DEVID, &reg_data);
    if (ret != 0)
        return -1;
    if ((reg_data & ADPD188_DEVID_DEV_ID_MASK) != 0x16)
        return -1;
?
    /** Enable 32kHz clock */
    ret = adpd188_reg_read(adpd_desc, ADPD188_REG_SAMPLE_CLK, &reg_data);
    if (ret != 0)
        return -1;
    reg_data |= ADPD188_SAMPLE_CLK_CLK32K_EN_MASK;
    ret = adpd188_reg_write(adpd_desc, ADPD188_REG_SAMPLE_CLK, reg_data);
    if (ret != 0)
        return -1;
?
    /* Activate program mode */
    ret = adpd188_mode_set(adpd_desc, ADPD188_PROGRAM);
    if (ret != 0)
        return -1;
?
    /* Initialize device in the datasheet smoke detection configuration */
    ret = adpd188_smoke_detect_setup(adpd_desc);
    if (ret != 0)
        return -1;
}